NOTICE: help.openstreetmap.org is no longer in use from 1st March 2024. Please use the OpenStreetMap Community Forum

Just installed OSM on Ubuntu 18.04 using the rather excellent guide published by the switch2osm folks.

Everything works up to and including the initial manual test of rendered.

When I try to go to the web page at http://yourserveripaddress/osm/0/0/0.png (yes, using the server's IP address) I get the following error;

The requested URL /osm/0/0/0.png was not found on this server

I've reviewed all of the steps and confess I am a bit confused, not that that is particularly unusual. I tend to get grumpy when I follow a recipe and I burn the cake... so to speak.

Any help would be most helpful.

asked 18 Sep '19, 07:24

amu306's gravatar image

amu306
11112
accept rate: 0%


Which instructions did you follow exactly - these: https://switch2osm.org/manually-building-a-tile-server-18-04-lts/ ? In that case (slightly non-intuitively perhaps) your tiles will be under /hot/ not under /osm/.

In any case double-check that you have made the necessary changes to the Apache config as documented, and if things still don't work let us see what appears in your /var/log/apache2/error.log when you make this request.

permanent link

answered 18 Sep '19, 07:36

Frederik%20Ramm's gravatar image

Frederik Ramm ♦
82.5k927201273
accept rate: 23%

I followed https://www.linuxbabe.com/linux-server/openstreetmap-tile-server-ubuntu-16-04 this article to setup tile server on ubuntu 18.04 . All is set up perfectly but the image was not found

(18 Sep '19, 09:24) amu306
2

Are you sure you used this guide. Because up there you said that you followed a switch2osm guide which is different. And the guide you have just quoted says "Then in your web browser address bar, type your-server-ip/osm_tiles/0/0/0.png" - but you apparently expected that "/osm/0/0/0.png" works. Where did you get that from? It appears that you might have burnt your cake by using a random mix of recipes!

(18 Sep '19, 09:43) Frederik Ramm ♦

this is what can be seen while rendering sudo -u tharakk renderd -f -c /usr/local/etc/renderd.conf

renderd[31905]: Rendering daemon started renderd[31905]: Initiating reqyest_queue renderd[31905]: Parsing section renderd renderd[31905]: Parsing render section 0 renderd[31905]: Parsing section mapnik renderd[31905]: Parsing section default renderd[31905]: Parsing section style2 renderd[31905]: config renderd: unix socketname=/var/run/renderd/renderd.sock renderd[31905]: config renderd: num_threads=4 renderd[31905]: config renderd: num_slaves=0 renderd[31905]: config renderd: tile_dir=/var/lib/mod_tile renderd[31905]: config renderd: stats_file=/var/run/renderd/renderd.stats renderd[31905]: config mapnik: plugins_dir=/usr/local/lib/mapnik/input renderd[31905]: config mapnik: font_dir=/usr/share/fonts/truetype/ttf-dejavu renderd[31905]: config mapnik: font_dir_recurse=1 renderd[31905]: config renderd(0): Active renderd[31905]: config renderd(0): unix socketname=/var/run/renderd/renderd.sock renderd[31905]: config renderd(0): num_threads=4

========================

(18 Sep '19, 13:18) amu306
1

Before you posted this you posted a link to your server IP which I will not repeat assuming you removed it on purpose. But that link proves that your mod_tile is working and that you have actually configured a /osm/ tile layer; however mod_tile immediately returns a 404 error for any tiles requested. Likely this is either because mod_tile cannot contact the renderd server - could be a freak local networking or security issue e.g. SELinux - or that mod_tile does contact the server but then gets an error message back. Check the /var/log/apache2/error.log for further info.

(18 Sep '19, 14:00) Frederik Ramm ♦

In my case, the 404 error occurred because the apache2 configuration was wrong. I put localhost in the apache2 settings. I checked /var/log/apache2/error.log for errors. When I changed localhost to IP, it worked fine.

permanent link

answered 20 Mar '23, 10:59

kharma77's gravatar image

kharma77
1
accept rate: 0%

Follow this question

By Email:

Once you sign in you will be able to subscribe for any updates here

By RSS:

Answers

Answers and Comments

Markdown Basics

  • *italic* or _italic_
  • **bold** or __bold__
  • link:[text](http://url.com/ "title")
  • image?![alt text](/path/img.jpg "title")
  • numbered list: 1. Foo 2. Bar
  • to add a line break simply add two spaces to where you would like the new line to be.
  • basic HTML tags are also supported

Question tags:

×710
×204

question asked: 18 Sep '19, 07:24

question was seen: 5,827 times

last updated: 20 Mar '23, 10:59

NOTICE: help.openstreetmap.org is no longer in use from 1st March 2024. Please use the OpenStreetMap Community Forum